Can you tell what it is yet.

Anything off topic, Pull up a chair and make yourself at home.
User avatar
nickjones
Site Admin
Posts: 2355
Joined: Tue Nov 20, 2012 12:54 am
Location: Clacton on Sea, Essex, UK

Re: Can you tell what it is yet.

Post by nickjones »

Just pulling your plonker mate.
I can't think how it can be used with chalk though?. I guess there must be a way,
Nick Jones.
In sunny Clacton-on-Sea, Essex, UK
tjlglass
Posts: 1121
Joined: Sun Sep 15, 2013 5:12 pm

Re: Can you tell what it is yet.

Post by tjlglass »

It was used on the molds that makes the toys so you rolled it by hand over the mold and the chalk showed the high/low points which showed that the mold has a raised/lowered edge so was not flat. The way it was discribed to me made perfect sense
GHOSTHUNTER
Moderator
Posts: 12249
Joined: Sun Sep 15, 2013 4:12 pm

Re: Can you tell what it is yet.

Post by GHOSTHUNTER »

There is a lot of truth in what tjlglass is saying.

I once worked in the petro-chemical industry by making control units, fuse protection units, safe rerouting control units etc, etc. All this stuff was sent to oil platforms, oil refinery plants and the like, so it was designed and made to international 'ISO' standards. Part of our testing equipment consisted of a wooden box,
very similar to the one shown, but very shallow and when opened, about five rows of ten tiny little 'tomb stones' were resting their backs on wooden supports.

What they were designed for is almost indentical to what tjlglass is saying, testing the trueness of dies and mould mating surfaces. In 'my' set, they were all made of the highest quality steel in a range of sizes. The thinnest could have been no more than a couple of millimeters thick, upto an inch thick. They were kept in their wooden case at all times and if you left one out on a worktop surface, you can expect the full wrath of the boss, because the set was rather expensive.

The interesting thing about this particular set, was that it was made by Rolls-Royce in their Metallurgy department and shown to me because of my interest in all aspects of R-R. I never used the set for my particular job, they were only used by the testing dept, but they were happy for me to see it.

It is fairly common knowledge that Rolls-Royce have one of the best metallurgy departments in the World and make some of the top branded golf clubs and hip replacement parts and I would not be at all surprised if they made the Lesney roller.

Regards,
GHOSTHUNTER.
User avatar
motorman
Moderator
Posts: 6863
Joined: Sun Sep 15, 2013 6:09 pm
Location: Glasgow, Scotland

Re: Can you tell what it is yet.

Post by motorman »

I am so disappointed i was sure it was a Nuclear Warhead. :cry:
MOTORMAN

"Kill all my demons and my angels will die too"
User avatar
zBret
Posts: 886
Joined: Fri Sep 20, 2013 9:31 pm

Re: Can you tell what it is yet.

Post by zBret »

motorman wrote:I am so disappointed i was sure it was a Nuclear Warhead. :cry:
I'm relieved, it wasn't "an over polished Jobby" :lol:

zBret
User avatar
zBret
Posts: 886
Joined: Fri Sep 20, 2013 9:31 pm

Re: Can you tell what it is yet.

Post by zBret »

nickjones wrote:Just pulling your plonker mate.
I have been enlightened once again, by the urban dictionary :D
I'd be lost without it...
http://www.urbandictionary.com/define.p ... %20plonker

zBret
User avatar
motorman
Moderator
Posts: 6863
Joined: Sun Sep 15, 2013 6:09 pm
Location: Glasgow, Scotland

Re: Can you tell what it is yet.

Post by motorman »

zBret wrote:
motorman wrote:I am so disappointed i was sure it was a Nuclear Warhead. :cry:
I'm relieved, it wasn't "an over polished Jobby" :lol:

zBret
So am i!! :lol:
MOTORMAN

"Kill all my demons and my angels will die too"
User avatar
MOKOSEX
Posts: 891
Joined: Sun Sep 15, 2013 10:39 pm

Re: Can you tell what it is yet.

Post by MOKOSEX »

GHOSTHUNTER wrote:There is a lot of truth in what tjlglass is saying.

I once worked in the petro-chemical industry by making control units, fuse protection units, safe rerouting control units etc, etc. All this stuff was sent to oil platforms, oil refinery plants and the like, so it was designed and made to international 'ISO' standards. Part of our testing equipment consisted of a wooden box,
very similar to the one shown, but very shallow and when opened, about five rows of ten tiny little 'tomb stones' were resting their backs on wooden supports.

What they were designed for is almost indentical to what tjlglass is saying, testing the trueness of dies and mould mating surfaces. In 'my' set, they were all made of the highest quality steel in a range of sizes. The thinnest could have been no more than a couple of millimeters thick, upto an inch thick. They were kept in their wooden case at all times and if you left one out on a worktop surface, you can expect the full wrath of the boss, because the set was rather expensive.

The interesting thing about this particular set, was that it was made by Rolls-Royce in their Metallurgy department and shown to me because of my interest in all aspects of R-R. I never used the set for my particular job, they were only used by the testing dept, but they were happy for me to see it.

It is fairly common knowledge that Rolls-Royce have one of the best metallurgy departments in the World and make some of the top branded golf clubs and hip replacement parts and I would not be at all surprised if they made the Lesney roller.

Regards,
GHOSTHUNTER.
The things you are describing are called slip gauges
dave
User avatar
MOKOSEX
Posts: 891
Joined: Sun Sep 15, 2013 10:39 pm

Re: Can you tell what it is yet.

Post by MOKOSEX »

tjlglass wrote:It was used on the molds that makes the toys so you rolled it by hand over the mold and the chalk showed the high/low points which showed that the mold has a raised/lowered edge so was not flat. The way it was discribed to me made perfect sense
I have never seen anything like this in the toolroom or foundry,to check for flatness you would use a straight edge ,and dies aren,t flat ,parts of it are but it would be a bit worrying rolling this beast around impressions,to me it looks like a roller from a coveyor,its possible someone found a use for it has a birmingham screw driver or another use in the toolroom,and the blue chalk?,i heard /used engineers paste which is blue and french chalk for marking out but not blue chalk.
I,m not doubting your mans usage or where it came from just puzzled,and loving this thread.I hope paul carr has the answer.
dave
Locked